Z-Wave Enrollment Guides

Energy

Garage Door Controller

• Enroll, delete, or factory reset a Linear Z-Wave Garage Controller (GD00Z)To access the full installation guide, see Linear Z-Wave Garage Controller (GD00Z) - Installation Guide. To enroll a Linear Z-Wave Garage Controller into a Z-Wave Network: To delete a Linear Z-Wave Garage Controller from a Z-Wave Network: The reset process should be performed after the device has been deleted from the Z-Wave network. The reset process causes the GD00Z to forget its network information, but it does not remove it from the Z-Wave controller (i.e., panel/module).
• Enroll, delete, or reset an EcoLink Z-Wave Plus Garage Controller (GDZW7-ECO)It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). If the Z-Wave controller is not SmartStart or S2-compatible, this device can be enrolled in the traditional way as an S0 device. If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling.

Lighting & Appliance Control

• Enroll a Qolsys IQ Lightbulb (QZ2110-840)The Qolsys IQ Lightbulb (QZ2110-840) can be enrolled into a Z-Wave network following the instructions below. For more information about installing a Qolsys IQ Lightbulb (QZ2110-840), see Qolsys IQ Lightbulb (QZ2110-840) - Installation Guide. To enroll a Qolsys IQ Lightbulb into a Z-Wave network: Apply power to the Qolsys IQ Lightbulb. If desired, edit the device’s name at the Z-Wave controller. Touch the add button on the Z-Wave controller to complete the pairing process.
• Enroll or delete a Linear Z-Wave Single Wall Outlet (WO15Z-1)The Linear Z-Wave Single Wall Outlet (WO15Z-1) can be enrolled into or deleted from a Z-Wave network following the instructions below. For more information about installing a Linear Z-Wave Single Wall Outlet (WO15Z-1), see Linear Z-Wave Single Wall Outlet (WO15Z-1) - Installation Guide. If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling.
• Enroll or delete a Qolsys IQ Outlet (QZ2131-840)It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). If the Z-Wave controller is not SmartStart or S2-compatible, this device can be enrolled in the traditional way as an S0 device. If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling.
• Enroll or delete an Evolve Z-Wave Duplex Wall Outlet (LOM-15)The Evolve Z-Wave Duplex Wall Outlet (LOM-15) can be enrolled into or deleted from a Z-Wave network following the instructions below. For more information about installing an Evolve Z-Wave Duplex Wall Outlet (LOM-15), see Evolve Z-Wave Duplex Wall Outlet (LOM-15) - Product Overview. Verify that the device shows up on the Alarm.com customer website or Alarm.com app and responds to commands to turn the Evolve Z-Wave Duplex Wall Outlet on/off.
• Enroll, delete, or reset a GE Fluorescent & Appliance Module (45603)The GE Fluorescent & Appliance Module (45603) can be enrolled into or deleted from a Z-Wave network following the instructions below. For more information about installing a GE Fluorescent & Appliance Module (45603), see GE Fluorescent & Appliance Module (45603) - Installation Guide. To enroll a GE Fluorescent & Appliance Module into a Z-Wave network: To delete and reset a GE Fluorescent & Appliance Module from a Z-Wave network:
• Enroll, delete, or reset a GE Light Dimmer Module (45602)The GE Light Dimmer Module (45602) can be enrolled into or deleted from a Z-Wave network following the instructions below. For more information about installing a GE Light Dimmer Module (45602), see GE Light Dimmer Module (45602) - Installation Guide. To enroll a GE Light Dimmer Module into a Z-Wave network: Verify that the device shows up on Alarm.com customer website or Alarm.com app and responds to commands to turn the device on/off. To delete a GE Light Dimmer Module from a Z-Wave network:
• Enroll, delete, or reset a GE Z-Wave Outlet (45605)Verify that the device shows up on the Alarm.com customer website or Alarm.com app and responds to commands to turn the GE Z-Wave outlet on/off. If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling. If the Z-Wave device is not responding to remote commands or experiencing other issues, see Z-Wave device is not functioning consistently.
• Enroll, delete, or reset a GoControl Plug-in Appliance Module (PS15EMZ5-1 or Linear PS15Z-2)The GoControl Plug-in Appliance Module (PS15EMZ5-1 or Linear PS15Z-2) can be enrolled into or deleted from a Z-Wave network following the instructions below. For more information about installing a GoControl Plug-in Appliance Module (PS15EMZ5-1 or Linear PS15Z-2), see GoControl Plug-in Appliance Module (PS15EMZ5-1 or Linear PS15Z-2) - Installation Guide. To delete and reset a GoControl Plug-in Appliance Module from a Z-Wave network:
• Enroll, delete, or reset a GoControl Plug-in Lamp Module (PD300EMZ5-1 or Linear PD300Z-2)The GoControl Plug-in Lamp Module (PD300EMZ5-1 or Linear PD300Z-2) can be enrolled into or deleted from a Z-Wave network following the instructions below. For more information about installing a GoControl Plug-in Lamp Module (PD300EMZ5-1 or Linear PD300Z-2), see GoControl Plug-in Lamp Module (PD300EMZ5-1 or Linear PD300Z-2) - Installation Guide. To enroll a GoControl Plug-in Lamp Module into a Z-Wave network: To delete and reset a GoControl Plug-in Lamp Module from a Z-Wave network:
• Enroll, delete, or reset a GoControl Smart LED Light Bulb (LB60Z-1)The GoControl Smart LED Light Bulb (LB60Z-1) can be enrolled into or deleted from a Z-Wave network following the instructions below. For more information about installing a GoControl Smart LED Light Bulb (LB60Z-1), see GoControl Smart LED Light Bulb (LB60Z-1) - Installation Guide. Verify that the device shows up on the Alarm.com customer website or app and responds to commands to turn the Smart LED Bulb on/off.
• Enroll, delete, or reset a GoControl Z-Wave In-Wall Switch (WS15Z5-1)The GoControl Z-Wave In-Wall Switch (WS15Z5-1) can be enrolled into or deleted from a Z-Wave network following the instructions below. If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling. If the Z-Wave device is not responding to remote commands or experiencing other issues, see Z-Wave device is not functioning consistently.
• Enroll, delete, or reset a GoControl Z-Wave Wall Dimmer Switch (WD500Z5-1)The GoControl Z-Wave Wall Dimmer Switch (WD500Z5-1) can be enrolled into or deleted from a Z-Wave network following the instructions below. For more information about installing a GoControl Z-Wave Wall Dimmer Switch (WD500Z5-1), see GoControl Z-Wave Wall Dimmer Switch (WD500Z5-1) - Installation and User Guide. If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling.
• Enroll, delete, or reset a Hank RGB Bulb (HKZW-RGB01)The Hank RGB Bulb (HKZW-RGB01) can be enrolled into or deleted from a Z-Wave network following the instructions below. Verify that the RGB Bulb shows up on the Alarm.com customer website and Alarm.com app and responds to commands to turn the RGB Bulb on/off. Removing the RGB Bulb from a Z-Wave network per the above instructions clears the memory on the RGB Bulb and erases all Z-Wave network and configuration information.
• Enroll, delete, or reset a Hank Smart Plug (HKZW-SO03)The Hank Smart Plug (HKZW-SO03) can be enrolled into or deleted from a Z-Wave network following the instructions below. For more information about installing a Hank Smart Plug (HKZW-SO03), see Hank Smart Plug (HKZW-SO03) - Installation Guide. To enroll a Hank Smart Plug into a Z-Wave network: Verify that the device shows up on Alarm.com customer website or Alarm.com app and responds to commands to turn the device on/off. To delete a Hank Smart Plug from a Z-Wave network:
• Enroll, delete, or reset a Hank Smart Plug (HKZW-SO09)The Hank Smart Plug (HKZW‑SO09) can be added to a Z‑Wave network as a SmartStart device, an S2‑encrypted device, or a legacy S0 device depending on controller compatibility.
• Enroll, delete, or reset a Jasco Enbrighten 800 Series Outdoor Plug-in Switch (76721)It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling. If the Z-Wave device is not responding to remote commands or experiencing other issues, see Z-Wave device is not functioning consistently.
• Enroll, delete, or reset a Jasco Enbrighten In-Wall Smart Switch (76592)It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling. If the Z-Wave device is not responding to remote commands or experiencing other issues, see Z-Wave device is not functioning consistently.
• Enroll, delete, or reset a Jasco Enbrighten LED Bulb (52190 or ZW7105)The Jasco Enbrighten LED Bulb (52190 or ZW7105) can be enrolled into or deleted from a Z-Wave network following the instructions below. For more information about installing a Jasco Enbrighten LED Bulb (52190 or ZW7105), see Jasco Enbrighten LED Bulb (52190 or ZW7105) - Installation Guide. It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices).
• Enroll, delete, or reset a Jasco Enbrighten No-Neutral Smart Dimmer (52252/52253/ZW3012)For more information about installing a Jasco Enbrighten No-Neutral Smart Dimmer (52252/52253/ZW3012), see Jasco Enbrighten No-Neutral Smart Dimmer (52252/52253/ZW3012) - Installation Guide. It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices).
• Enroll, delete, or reset a Jasco Enbrighten Smart A19 LED Bulb (39723)For more information about installing a Jasco Enbrighten Smart A19 LED Bulb (39723), see Jasco Enbrighten Smart A19 LED Bulb (39723) - Quick Start Guide. The LED Smart Bulb will be added to the network within 30 seconds, and the bulb will flash twice to signify a successful enrollment. Verify that the LED Smart Bulb shows up on the Alarm.com customer website and responds to commands to turn the LED Smart Bulb on/off.
• Enroll, delete, or reset a Jasco In-Wall Smart Toggle Dimmer (14322/14296/14295/ZW3004)The Jasco In-Wall Smart Toggle Dimmer (14322/14296/14295/ZW3004) can be enrolled into or deleted from a Z-Wave network following the instructions below. For more information about installing a Jasco In-Wall Smart Toggle Dimmer (14322/14296/14295/ZW3004), see Jasco In-Wall Smart Toggle Dimmer (14322/14296/14295/ZW3004) - Quick Start Guide. If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling.
• Enroll, delete, or reset a Jasco In-Wall Smart Toggle Switch (14319/ZW4003)The Jasco In-Wall Smart Toggle Switch (14319/ZW4003) can be enrolled into or deleted from a Z-Wave network following the instructions below. For more information about installing a Jasco In-Wall Smart Toggle Switch (14319/ZW4003), see Jasco In-Wall Smart Toggle Switch (14319/ZW4003) - Quick Start Guide. To enroll a Jasco In-Wall Smart Toggle Switch into a Z-Wave network: Quickly press up on the switch toggle three times, then immediately press down on the switch toggle three times.
• Enroll, delete, or reset a Jasco In-Wall Tamper Resistant Smart Outlet (14315/ZW1002)For more information about installing a Jasco In-Wall Tamper Resistant Smart Outlet (14315/ZW1002), see Jasco In-Wall Tamper Resistant Smart Outlet (14315/ZW1002) - Quick Start Guide. Verify that the device shows up on the Alarm.com customer website or Alarm.com app and responds to commands to turn the Jasco In-Wall Tamper Resistant Smart Outlet on/off.
• Enroll, delete, or reset a Jasco Lamp Dimmer 45653 (ZW3102)The Jasco Lamp Dimmer 45653 (ZW3102) can be enrolled into or deleted from a Z-Wave network following the instructions below. For more information about installing a Jasco Lamp Dimmer 45653 (ZW3102), see Jasco Lamp Dimmer 45653 (ZW3102) - Installation Guide. To enroll a Jasco Lamp Dimmer into a Z-Wave network: To delete and reset a Jasco Lamp Dimmer from a Z-Wave network:
• Enroll, delete, or reset a Jasco or GE/Enbrighten In-Wall Smart Paddle Dimmer (46564 or 46203)For more information about installing a Jasco or GE/Enbrighten In-Wall Smart Paddle Dimmer (46564 or 46203), see Jasco or GE/Enbrighten In-Wall Smart Paddle Dimmer (46564 or 46203) - Quick Start Guide. It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices).
• Enroll, delete, or reset a Jasco or GE/Enbrighten In-Wall Smart Paddle Switch (46562 or 46201)The Jasco or GE/Enbrighten In-Wall Smart Paddle Switch (46562 or 46201) can be enrolled into or deleted from a Z-Wave network following the instructions below. For more information about installing a Jasco or GE/Enbrighten In-Wall Smart Paddle Switch with S2 (46562 or 46201), see Jasco or GE/Enbrighten In-Wall Smart Paddle Switch (46562 or 46201) - Quick Start Guide.
• Enroll, delete, or reset a Jasco or GE/Enbrighten In-Wall Smart Toggle Dimmer (46565 or 46204)For more information about installing a Jasco or GE/Enbrighten In-Wall Smart Toggle Dimmer (46565 or 46204), see Jasco or GE/Enbrighten In-Wall Smart Toggle Dimmer (46565 or 46204) - Quick Start Guide. It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices).
• Enroll, delete, or reset a Jasco or GE/Enbrighten In-Wall Smart Toggle Switch (46563 or 46202)The Jasco or GE/Enbrighten In-Wall Smart Toggle Switch 46563 or 46202 can be enrolled into or deleted from a Z-Wave network following the instructions below. For more information about installing a Jasco or GE/Enbrighten In-Wall Smart Toggle Switch with S2 46563 or 46202, see Jasco or GE/Enbrighten In-Wall Smart Toggle Switch 46563 or 46202 - Quick Start Guide.
• Enroll, delete, or reset a Jasco or GE/Enbrighten Plug-in Outdoor Smart Switch (14325 or 14298)For more information about installing a Jasco or GE/Enbrighten Plug-in Outdoor Smart Switch (14325 or 14298), see Jasco or GE/Enbrighten Plug-in Outdoor Smart Switch (14325 or 14298) - Quick Start Guide. It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices).
• Enroll, delete, or reset a Jasco Plug-in Outdoor Smart Switch 14311 (ZW4201)The Jasco Plug-in Outdoor Smart Switch 14311 (ZW4201) can be enrolled into or deleted from a Z-Wave network following the instructions below. For more information about installing a Jasco Plug-in Outdoor Smart Switch 14311 (ZW4201), see Jasco Plug-in Outdoor Smart Switch 14311 (ZW4201) - Installation Guide. To enroll a Jasco Plug-in Outdoor Smart Switch into a Z-Wave network: To delete a Jasco Plug-in Outdoor Smart Switch from a Z-Wave network: To reset a Jasco Plug-in Outdoor Smart Switch:
• Enroll, delete, or reset a Jasco Plug-in Smart Switch (28172 or ZW4104)The Jasco Plug-in Smart Switch (28172 or ZW4104) can be enrolled into or deleted from a Z-Wave network following the instructions below. For more information about installing a Jasco Plug-in Smart Switch (28172 or ZW4104), see Jasco Plug-in Smart Switch (28172 or ZW4104) - Installation Guide. To enroll a Jasco Plug-in Smart Switch into a Z-Wave network: To delete a Jasco Plug-in Smart Switch from a Z-Wave network:
• Enroll, delete, or reset a Jasco Plug-in Wireless Smart Dimmer 28166/28170 (ZW3104)The Jasco Plug-in Wireless Smart Dimmer 28166 (ZW3104) can be enrolled into or deleted from a Z-Wave network following the instructions below. For more information about installing a Jasco Plug-in Wireless Smart Dimmer 28166 (ZW3104), see Jasco Plug-in Wireless Smart Dimmer 28166 (ZW3104) - Installation Guide. To enroll a Jasco Plug-in Wireless Smart Dimmer into a Z-Wave network: To delete a Jasco Plug-in Wireless Smart Dimmer from a Z-Wave network:
• Enroll, delete, or reset a Jasco Pro Series Plug-In Smart Switch (76724)It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling. If the Z-Wave device is not responding to remote commands or experiencing other issues, see Z-Wave device is not functioning consistently.
• Enroll, delete, or reset a Jasco Pro Series Plug-In Smart Switch (79244)It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). Press and hold the Program button on the smart switch for at least 3 seconds and continue holding the button while plugging the smart switch back in. If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling.
• Enroll, delete, or reset a Jasco Pro Series Smart LED Bulb (76609)The Jasco Pro Series Smart LED Bulb (76609) can be enrolled into or deleted from a Z-Wave network following the instructions below. It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling.
• Enroll, delete, or reset a Jasco Z-Wave In-Wall Smart Dimmer (14321)The Jasco Z-Wave In-Wall Smart Dimmer (14321) can be enrolled into or deleted from a Z-Wave network following the instructions below. For more information about installing a Jasco Z-Wave In-Wall Smart Dimmer (14321), see Jasco Z-Wave In-Wall Smart Dimmer (14321) - Installation Guide. If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling.
• Enroll, delete, or reset a Jasco Z-Wave In-Wall Wireless Smart Switch (14318)The Jasco Z-Wave In-Wall Wireless Smart Switch (14318) can be enrolled into or deleted from a Z-Wave network following the instructions below. For more information about installing a Jasco Z-Wave In-Wall Wireless Smart Switch, see Jasco Z-Wave In-Wall Wireless Smart Switch (14318) - Installation Guide. To enroll a Jasco Z-Wave In-Wall Wireless Smart Switch into a Z-Wave network: To delete a Jasco Z-Wave In-Wall Wireless Smart Switch from a Z-Wave network:
• Enroll, delete, or reset a Jasco Z-Wave Interchangeable Paddle In-wall On/Off Switch 45709 (ZW4005)The Jasco Z-Wave Interchangeable Paddle In-wall On/Off Switch 45709 (ZW4005) can be enrolled into or deleted from a Z-Wave network following the instructions below. If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling. If the Z-Wave device is not responding to remote commands or experiencing other issues, see Z-Wave device is not functioning consistently.
• Enroll, delete, or reset a JascoPro™ 700 Series Duplex Receptacle, Tamper Resistant (59387)It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling. If the Z-Wave device is not responding to remote commands or experiencing other issues, see Z-Wave device is not functioning consistently.
• Enroll, delete, or reset a JascoPro™ 700 Series In-Wall Toggle Dimmer (59384)It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling. If the Z-Wave device is not responding to remote commands or experiencing other issues, see Z-Wave device is not functioning consistently.
• Enroll, delete, or reset a JascoPro™ In-Wall Smart Dimmer (76596/76597)It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling. If the Z-Wave device is not responding to remote commands or experiencing other issues, see Z-Wave device is not functioning consistently.
• Enroll, delete, or reset a JascoPro™ Plug-In Dimmer (76723)It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling. If the Z-Wave device is not responding to remote commands or experiencing other issues, see Z-Wave device is not functioning consistently.
• Enroll, delete, or reset a Leviton In-Wall Dimmer (DZ6HD)The Leviton In-Wall Dimmer (DZ6HD) can be enrolled into or deleted from a Z-Wave network following the instructions below. Verify that the device shows up on the Alarm.com customer website or Alarm.com app and responds to commands to turn the device on/off. Release the top of the switch paddle to reset the switch. If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling.
• Enroll, delete, or reset a Leviton In-Wall Switch (DZ15S)The Leviton In‑Wall Switch (DZ15S) can be added to, removed from, or reset on a Z‑Wave network using the switch paddle and a Z‑Wave controller.
• Enroll, delete, or reset a Leviton Plug-In Dimmer (DZPD3)The Leviton Plug-In Dimmer (DZPD3) can be enrolled into or deleted from a Z-Wave network following the instructions below. For more information about installing a Leviton Plug-In Dimmer (DZPD3), see Leviton Plug-In Dimmer (DZPD3) - Installation Guide. The device is now ready to add to the Z-Wave network. The Z-Wave controller will begin to pair with the device. Upon successful addition to the network, the LED will turn and then blink green three times.
• Enroll, delete, or reset a Leviton Plug-In Outlet (DZPA1)The Leviton Plug-In Outlet (DZPA1) can be enrolled into or deleted from a Z-Wave network following the instructions below. For more information about installing a Leviton Plug-In Outlet (DZPA1), see Leviton Plug-In Outlet (DZPA1) - Installation Guide. The device is now ready to add to the Z-Wave network. The Z-Wave controller will begin to pair with the device. Upon successful addition to the network, the LED will turn and then blink green three times.
• Enroll, delete, or reset a Leviton Smart Dimmer Switch, 800 Series (ZW6HD)It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling. If the Z-Wave device is not responding to remote commands or experiencing other issues, see Z-Wave device is not functioning consistently.
• Enroll, delete, or reset a Leviton Smart Outlet, 700 Series (ZW15R)It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). If the Z-Wave controller is not SmartStart or S2-compatible, this device can be enrolled in the traditional way as an S0 device. If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling.
• Enroll, delete, or reset a Leviton Smart Switch, 800 Series (ZW15S)It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling. If the Z-Wave device is not responding to remote commands or experiencing other issues, see Z-Wave device is not functioning consistently.
• Enroll, delete, or reset a Qolsys IQ Dimmer (QZ2140-840)Verify that the device shows up on the Alarm.com customer website or Alarm.com app and responds to commands to turn the Qolsys IQ Z-Wave Outlet on/off. Unplug the IQ Outlet from the AC outlet as well as the power plug of the appliance from the IQ Dimmer (if plugged in). If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling.
• Enroll, delete, or reset a Qolsys IQ Plug-In Dimmer (QZ2141-840)The Qolsys IQ Plug-In Dimmer (QZ2141-840) can be enrolled into or deleted from a Z-Wave network following the instructions below.
• Enroll, delete, or reset a Qolsys IQ SmartPlug (QZ2101-840)The Qolsys IQ SmartPlug (QZ2101-840) can be enrolled into or deleted from a Z-Wave network following the instructions below. If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling. If the Z-Wave device is not responding to remote commands or experiencing other issues, see Z-Wave device is not functioning consistently.
• Enroll, delete, or reset a Qolsys IQ Z-Wave Outlet (QZ2130-840)The Qolsys IQ Z-Wave Outlet (QZ2130-840) can be enrolled into or deleted from a Z-Wave network following the instructions below. Verify that the device shows up on the Alarm.com customer website or Alarm.com app and responds to commands to turn the Qolsys IQ Z-Wave Outlet on/off. Unplug the IQ Outlet from the AC outlet as well as the power plugs of the lighting from the module (if plugged in).
• Enroll, delete, or reset a Schneider Electric Z-Wave Dimmer (SQR22102WHZ)The Schneider Electric Z-Wave Dimmer (SQR22102WHZ) can be enrolled into or deleted from a Z-Wave network following the instructions below.
• Enroll, delete, or reset a Schneider Electric Z-Wave Receptacle (SQR44102WHZ)The Schneider Electric Z-Wave Receptacle (SQR44102WHZ) can be enrolled into or deleted from a Z-Wave network
• Enroll, delete, or reset a Schneider Electric Z-Wave Remote Switch (SQR50101WHZ)The Schneider Electric Z-Wave Remote Switch (SQR50101WHZ) can be enrolled into or deleted from a Z-Wave network following the instructions below.
• Enroll, delete, or reset a Schneider Electric Z-Wave Smart Plug (SQR62102WHZ)For more information about installing a Schneider Electric Z-Wave Smart Plug (SQR62102WHZ), see Schneider Electric Z-Wave Smart Plug (SQR62102WHZ) - Installation Guide. It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices).
• Enroll, delete, or reset a Schneider Square D X Series Switch (SQ14102WHZ)For more information about installing a Schneider Square D X Series Switch (SQ14102WHZ), see Schneider Square D X Series Switch (SQ14102WHZ) - Installation Guide. It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices).
• Enroll, delete, or reset a Sengled LED BulbThe Sengled LED Bulb (V11-N13-US) can be enrolled into or deleted from a Z-Wave network following the instructions below.
• Enroll, delete, or reset a Shelly Qubino Wave 1It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). The attached load will be toggled on and off twice when the Wave 1 Relay is successfully added to the Z-Wave network. The attached load will be toggled on and off twice when the Wave 1 Relay is successfully removed from the Z-Wave network
• Enroll, delete, or reset a Shelly Qubino Wave 1PM MiniIt is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). Quickly release and then press and hold the S button on the device until the blue LED starts blinking in mode 3. If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling.
• Enroll, delete, or reset a Shelly Qubino Wave PlugIt is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). If the Z-Wave controller is not SmartStart or S2-compatible, this device can be enrolled in the traditional way as an S0 device. If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling.
• Enroll, delete, or reset a Shelly Qubino Wave Pro ShutterIt is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). The green LED will blink slowly if the Wave Pro Shutter is successfully added to the Z-Wave network. The blue LED will begin to blink slowly when the Wave Pro Shutter is successfully removed from the Z-Wave network.
• Enroll, delete, or reset a Shelly Wave Outdoor Plug SEnroll, delete, or reset instructions for a Shelly Wave Plug S
• Enroll, delete, or reset a Shelly Wave Plug SEnroll, delete, or reset instructions for a Shelly Wave Plug S
• Enroll, delete, or reset a Shelly Wave Pro 1PMIt is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). Quickly release and then press and hold the S button on the device until the blue LED starts blinking in mode 3. If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling.
• Enroll, delete, or reset a Zipato RGBW Light Bulb (Gen 2)The Zipato RGBW Light Bulb (Gen 2) can be enrolled into or deleted from a Z-Wave network following the instructions below. For more information about installing a Zipato RGBW Light Bulb (Gen 2), see Zipato RGBW Light Bulb (Gen 2) - Installation Guide. To enroll the Zipato RGBW Light Bulb (Gen 2) into a Z-Wave network: To delete the Zipato RGBW Light Bulb (Gen 2) from a Z-Wave network: To manually reset the Zipato RGBW Light Bulb (Gen 2):
• Enroll, delete, or reset a Zooz ZEN77 800LR In-Wall SwitchIt is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling. If the Z-Wave device is not responding to remote commands or experiencing other issues, see Z-Wave device is not functioning consistently.
• Enroll, delete, or reset an Eaton Z-Wave In-Wall On/Off Switch (RF9601)The Eaton Z-Wave In-Wall On/Off Switch (RF9601) can be enrolled into or deleted from a Z-Wave network following the instructions below.
• Enroll, delete, or reset an Eaton Z-Wave In-Wall Smart Dimmer & Accessory Dimmer (RF9640-ND/RF9642-ZD)The Eaton Z-Wave In-Wall Smart Dimmer & Accessory Dimmer (RF9640-ND/RF9642-ZD) can be enrolled into or deleted from a Z-Wave network following the instructions below. For more information about installing an Eaton Z-Wave In-Wall Smart Dimmer & Accessory Dimmer (RF9640-ND/RF9642-ZD), see Eaton Z-Wave In-Wall Smart Dimmer & Accessory Dimmer (RF9640-ND/RF9642-ZD) - Installation Guide. To enroll an Eaton Z-Wave In-Wall Smart Dimmer & Accessory Dimmer into a Z-Wave network:
• Enroll, delete, or reset an Eaton Z-Wave Outlet (RFTR9605-T)The Eaton Z-Wave Outlet (RFTR9605-T) can be enrolled into or deleted from a Z-Wave network following the instructions below. If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling. If the Z-Wave device is not responding to remote commands or experiencing other issues, see Z-Wave device is not functioning consistently. If the Z-Wave device is not communicating at all, see Z-Wave device is in malfunction or offline.
• Enroll, delete, or reset an Evolve In-Wall Dimmer (LRM-AS or LRM-15)The Evolve In-Wall Dimmer (LRM-AS or LRM-15) can be enrolled into or deleted from a Z-Wave network following the instructions below. For more information about installing an Evolve In-Wall Dimmer (LRM-AS or LRM-15), see Evolve In-Wall Dimmer (LRM-AS or LRM-15) - Installation Guide. If the Z-Wave device is not responding to remote commands or experiencing other issues, see Z-Wave device is not functioning consistently.
• Enroll, delete, or reset an iblinds V3.1 Z-Wave Window Blind MotorIt is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling. If the Z-Wave device is not responding to remote commands or experiencing other issues, see Z-Wave device is not functioning consistently.
• Enroll, delete, or reset an iDevices Z-Wave In-Wall Smart Dimmer (IDEVZ05DW/61303)It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling. If the Z-Wave device is not responding to remote commands or experiencing other issues, see Z-Wave device is not functioning consistently.
• Enroll, delete, or reset an iDevices Z-Wave In-Wall Smart Switch (IDEVZ01DW/61301)It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling. If the Z-Wave device is not responding to remote commands or experiencing other issues, see Z-Wave device is not functioning consistently.
• Enroll, delete, or reset an iDevices Z-Wave In-Wall Tamper Resistant Smart Outlet (IDEVZ08W/61304)For more information about installing an iDevices Z-Wave In-Wall Tamper Resistant Smart Outlet (IDEVZ08W/61304), see iDevices Z-Wave In-Wall Tamper Resistant Smart Outlet (IDEVZ08W/61304) - Installation Guide. It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices).
• Enroll, delete, or reset an inovelli Black Series Dimming Smart Switch (LZW31)For more information about installing an inovelli Black Series Dimming Smart Switch (LZW31), see inovelli Black Series Dimming Smart Switch (LZW31) - Installation Guide. It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices).
• Enroll, delete, or reset an inovelli Black Series On/Off Smart Switch (LZW30)For more information about installing an inovelli Black Series On/Off Smart Switch (LZW30), see inovelli Black Series On/Off Smart Switch (LZW30) - Installation Guide. It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices).
• Enroll, delete, or reset an inovelli Red Series Dimmer Smart Switch with Scenes (LZW31-SN)For more information about installing a inovelli Red Series Dimmer Smart Switch with Scenes, see inovelli Red Series Dimmer Smart Switch with Scenes (LZW31-SN) - Installation Guide. It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices).
• Enroll, delete, or reset an inovelli Red Series On/Off Smart Switch with Scenes (LZW30-SN)For more information about installing an inovelli Red Series On/Off Smart Switch with Scenes (LZW30-SN), see inovelli Red Series On/Off Smart Switch with Scenes (LZW30-SN) - Installation Guide. It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices).
• Enroll, delete, or reset an inovelli RGBW Multi-Color Bulb (LZW42)The inovelli RGBW Multi-Color Bulb (LZW42) can be enrolled into or deleted from a Z-Wave network following the instructions below. For more information about installing an inovelli RGBW Multi-Color Bulb (LZW42), see inovelli RGBW Multi-Color Bulb (LZW42) - Installation Guide. To enroll an inovelli RGBW Multi-Color Bulb (LZW42) into a Z-Wave network: To delete an inovelli RGBW Multi-Color Bulb (LZW42) from a Z-Wave network: To reset an inovelli RGBW Multi-Color Bulb (LZW42:
• Enroll, delete, or reset an inovelli Z-Wave® Long Range Smart Dimmer (VZW31-SN)For more information about installing an inovelli Z-Wave® Long Range Smart Dimmer (VZW31-SN), see inovelli Z-Wave® Long Range Smart Dimmer (VZW31-SN) - Installation Guide. It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices).
• Shelly Wave 2PMThe Wave 2PM (Device) is a single product that enables remote control of two electrical devices such as bulbs, ceiling fans, and IR heaters. It switches (on/off) two independent loads and measures their power consumption separately and in total. The Device is compatible with switches (default) and push-buttons.
• Zooz ZEN74 800LR Toggle Dimmer SwitchFeatures Include: Z-Wave S2 & SmartStart Compatible • On/Off/Dim • Remote Control of Device, including Rules & Scenes

Locks

• Enroll or delete a Danalock V3 Smart LockWith this added security, the lock and the controller must use additional Z-Wave commands to enroll and communicate. If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling. If the Z-Wave device is not responding to remote commands or experiencing other issues, see Z-Wave device is not functioning consistently. If the Z-Wave device is not communicating at all, see Z-Wave device is in malfunction or offline.
• Enroll or delete a Yale Assure Push Button Lever Lock (YRL216)With this added security, the lock and the controller must use additional Z-Wave commands to learn-in and communicate. To mitigate the chances of a learn-in failure for locks, complete the following during installation. To enroll a Yale Assure Push Button Lever Lock (YRL216) into a Z-Wave network: To delete a Yale Assure Push Button Lever Lock (YRL216) from a Z-Wave network: Enter the master code, followed by a press of the [⚙ Gear Button].
• Enroll or delete a Yale Real Living Push Button Deadbolt (YRD210)With this added security, the lock and the controller must use additional Z-Wave commands to enroll and communicate. For information about hardware installation, see Yale Real Living Push Button Deadbolt (YRD210) - Installation guide. Important: Do not add or delete user codes locally to or from the lock. To enroll a Yale Real Living Push Button Deadbolt (YRD210) into a Z-Wave network: To delete a Yale Real Living Push Button Deadbolt (YRD210) from a Z-Wave network:
• Enroll, delete, or reset a Baldwin Keyless Entry Deadbolt (8252/8285)With this added security, the lock and the controller must use additional Z-Wave commands to enroll and communicate. Press the A button on the lock one time to pair it to the Z-Wave Controller. Press the A button one time on the lock to delete it from the Z-Wave Controller. Continue holding the button for 30 seconds until the lock beeps and the status LED flashes red. After 20 seconds, the status LED will flash green, and the lock will beep once to indicate it has been reset.
• Enroll, delete, or reset a Kaadas Z-Wave Fingerprint Keypad Deadbolt (KA202)It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling. If the Z-Wave device is not responding to remote commands or experiencing other issues, see Z-Wave device is not functioning consistently.
• Enroll, delete, or reset a Kaadas Z-Wave Key Free Keypad Deadbolt (KA200)It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling. If the Z-Wave device is not responding to remote commands or experiencing other issues, see Z-Wave device is not functioning consistently.
• Enroll, delete, or reset a Kaadas Z-Wave Key-Free Touchpad Deadbolt (KA210)It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling. If the Z-Wave device is not responding to remote commands or experiencing other issues, see Z-Wave device is not functioning consistently.
• Enroll, delete, or reset a Kaadas Z-Wave Keypad Deadbolt (KA201)It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling. If the Z-Wave device is not responding to remote commands or experiencing other issues, see Z-Wave device is not functioning consistently.
• Enroll, delete, or reset a Kaadas Z-Wave Touchpad Deadbolt (KA211)It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling. If the Z-Wave device is not responding to remote commands or experiencing other issues, see Z-Wave device is not functioning consistently.
• Enroll, delete, or reset a Kwikset/Weiser Home Connect 620It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling. If the Z-Wave device is not responding to remote commands or experiencing other issues, see Z-Wave device is not functioning consistently.
• Enroll, delete, or reset a Philips Smart Deadbolt (DDL240X-1HB)It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling. If the Z-Wave device is not responding to remote commands or experiencing other issues, see Z-Wave device is not functioning consistently.
• Enroll, delete, or reset a Schlage J Series Lock (JBE109 and JFE109)It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). If the Z-Wave controller is not SmartStart or S2-compatible, this device can be enrolled in the traditional way as an S0 device. Enter the 5 digit code shown on the label located on the lock or on the cover of the included installation instructions.
• Enroll, delete, or reset a Yale Assure Lock 2 Pro Deadbolt/Yale Pro® 2 ZW3 LockIf the Z-Wave controller is not SmartStart or S2-compatible, this device can be enrolled in the traditional way as an S0 device. Press the small black button on the interior of the lock until 1 and ⚙ are illuminated. If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling. If the Z-Wave device is not responding to remote commands or experiencing other issues, see Z-Wave device is not functioning consistently.
• Enroll, delete, or reset a Yale nexTouch Commercial Grade One Cylindrical Keypad Lever Lock (NTB612)This guide explains how to enroll, delete, reset, and troubleshoot a Yale nexTouch NTB612 lock on a Z-Wave network.
• Enroll, delete, or reset a Yale Pro SL Key-Free Pushbutton Deadbolt (YRD136)To enroll a Yale Pro SL Key-Free Pushbutton Deadbolt (YRD136) into a Z-Wave network: If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling. If the Z-Wave device is not responding to remote commands or experiencing other issues, see Z-Wave device is not functioning consistently. If the Z-Wave device is not communicating at all, see Z-Wave device is in malfunction or offline.
• Enroll, delete, or reset a Yale Real Living Key Free Touchscreen Lock (YRD446)With this added security, the lock and the controller must use additional Z-Wave commands to enroll and communicate. If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling. If the Z-Wave device is not responding to remote commands or experiencing other issues, see Z-Wave device is not functioning consistently. If the Z-Wave device is not communicating at all, see Z-Wave device is in malfunction or offline.
• Enroll, delete, or reset a Yale/Fortune Brands NexTouch Lever Locks (FBB618 and FBB628)It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). If the Z-Wave controller is not SmartStart-compatible, it is recommended to enroll this device as an S2 device for enhanced security and encryption features. If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling.
• Enroll, delete, or reset an Alfred DB2S LockIt is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). If the Z-Wave controller is not SmartStart-compatible, it is recommended to enroll this device as an S2 device for enhanced security and encryption features. If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling.
• Enroll, delete, or reset an Alfred ML2 Mortise LockIt is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). If the Z-Wave controller is not SmartStart-compatible, it is recommended to enroll this device as an S2 device for enhanced security and encryption features. If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling.
• Enroll, delete, or reset an DB1 Pro LockIt is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). If the Z-Wave controller is not SmartStart-compatible, it is recommended to enroll this device as an S2 device for enhanced security and encryption features. If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling.

Thermostats

• Enroll, delete, or reset an Aidoo Z-Wave Plus ThermostatIt is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). To factory reset, press the Factory Reset button (gray recessed button on the top of the Aidoo Z-Wave Plus) for 10 seconds or until all LEDs on the front of the device blink simultaneously.
• Enroll, delete, or reset an Alarm.com Temperature Sensor (ADC-S40-T)The Alarm.com Temperature Sensor (ADC‑S40‑T) can be added to a Z‑Wave network as a SmartStart, S2, or S0 device depending on controller compatibility.

Water

• Enroll, delete, or reset a Jasco Smart Flood/Freeze SensorEnroll a Jasco Smart Flood/Freeze Sensor into a Z-Wave network using SmartStart, S2, or S0, depending on controller compatibility.
• Enroll, delete, or reset a Zooz Titan Water Valve ActuatorIt is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). If the Z-Wave controller is not SmartStart or S2-compatible, this device can be enrolled in the traditional way as an S0 device. If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling.
• Enroll, delete, or reset an IQ Water Valve (QZ2160-840)It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices). If the Z-Wave controller is not SmartStart-compatible, it is recommended to enroll this device as an S2 device for enhanced security and encryption features. The water valve is in inclusion mode when the LED is flashing yellow and the device is beeping.

Troubleshooting