Shelly Wave 2PM
Quick Facts
| Device Image |  |
|---|---|
| Manufacturer | Shelly |
| Power Requirements | 110-240 V AC / 24 V DC +/- 10% |
| Maximum Load | 16 A |
| Dimming | Incompatible |
| Z-Wave Security 2 (S2) | Compatible |
| Z-Wave SmartStart | Compatible |
| Z-Wave Multi-Channel | Compatible |
| Z-Wave Frequency |
|
The Shelly Wave 2PM can be enrolled into or deleted from a Z-Wave network following the instructions below.
For more information about installation, see the manufacturer's Shelly Wave 2PM - Installation Guide.
To enroll a Shelly Wave 2PM:
This device can be enrolled using the method as a SmartStart, S2, or S0 device.
To enroll as a SmartStart device:
It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices).
For information about SmartStart compatibility and the enrollment process, see Add or remove a Z-Wave SmartStart-enabled device.
To enroll as an S2 device:
If the Z-Wave controller is not SmartStart-compatible, it is recommended to enroll this device as an S2 device for enhanced security and encryption features.
For information about this process, see Add an S2-encrypted Z-Wave device.
To enroll as an S0 device:
If the Z-Wave controller is not SmartStart or S2-compatible, this device can be enrolled in the traditional way as an S0 device using an attached switch/power button or using the S button.
To enroll using an attached switch/power button:
- Verify the device is connected to power.
- Verify the blue LED is blinking in Mode 1. If so, the device is not added to a Z-Wave network.
- Place the Z-Wave controller into Add Mode.
- Toggle the switch/power button three times within 3 seconds.
- The blue LED will blink in Mode 2 (0.5s on, 0.5s off) during the inclusion process.
- The green LED will blink in Mode 1 (0.5s On, 2s Off) when the device is successfully added to the Z-Wave® network.
To enroll using the S button:
- Verify the device is connected to power and the blue LED is blinking in Mode 1. If so, the device is not added to a Z-Wave network.
- Place the Z-Wave controller into Add Mode.
- Quickly press and hold the S button on the Device until the LED turns solid blue.
- Quickly release and then press and hold (> 2s) the S button on the Device until the blue LED starts blinking in Mode 3. Releasing the S button will start the Learn mode.
- The blue LED will blink in Mode 2 (0.5s on, 0.5s off) during the inclusion process.
- The green LED will blink in Mode 1 (0.5s On, 2s Off) when the device is successfully added to the Z-Wave® network.
To delete a Shelly Wave 2PM:
This device can be deleted using an attached switch/power button or using the S button.
To delete the device using an attached switch/power button:
- Place the Z-Wave controller into Delete Mode.
- Toggle the attached switch on and off three times within 3 seconds.
- The LED will blink during the exclusion process.
- The attached load will be toggled on and off twice when the device is successfully removed from the Z-Wave network
To delete the device using the S button:
- Place the Z-Wave controller into Delete Mode.
- Toggle the attached switch on and off three times within 3 seconds.
- Press and hold the S button until the LED turns solid blue.
- Release, then press and hold the S button for at least 2 seconds.
- Release the S button when the LED begins rapidly flashing.
To reset a Shelly Wave 2PM:
This device can be reset using an attached switch/power button or using the S button.
To reset the device using an attached switch/power button:
- Ensure the device has power.
- Verify the device is connected to power.
- Toggle the attached switch/power button on and off five times within 3 seconds.
- During the reset the LED will turn solid green for about 1 second, then the red and blue LED will blink for about 2 seconds.
- The blue LED will blink if the factory reset is successful.
To reset the device using the S button:
- Ensure the device has power.
- Press and hold the S button until the LED turns solid blue.
- Press the S button multiple times, until the LED turns solid red.
- Release, then press and hold the S button for at least 2 seconds.
- Release the S button when the red LED begins rapidly flashing.
- During the reset, the LED will turn solid green for about 1 second, then the red and blue LED will blink for about 2 seconds.
- The blue LED will blink if the factory reset is successful.
Troubleshooting