Indoor Fixed w/IR (ADC-V522IR) - Data Sheet
Crystal-clear 1080p HD video, infrared night vision and secure cloud recording make the ADC-V522IR Wi-Fi Video Camera from Alarm.com ideal for indoor video monitoring. With its compact design and flexible mounting options, the ADC-V522IR is easy to install – whether mounted on a wall or ceiling or simply placed on a shelf.
Features
- HD 1080p video
- IR night vision
- Wide dynamic range (WDR)
- Two-Way Audio (see Two-Way Audio Compatibility FAQ)
- Video Analytics 1.0, Video Motion Detection, and sensor-triggered clips saved to the cloud
Included accessories
- Wi-Fi Video camera
- Camera stand
- Quick Installation Guide
- Mounting hardware
- Power adapter (10 feet)
Specifications
| Maximum resolution | 1920x1080 |
|---|---|
| Recording compression | H.264, MPEG-4 |
| Image sensor | 1/2.9" CMOS, 2.12 MP, 1920x1080 |
| Lens | 2.8 mm, F1.85 |
| Angle of view | 113° |
| Low-light sensitivity | 0 lux with IR |
| IR range | Up to 5 meters (~15 feet) |
| Image adjustments | Flip, brightness, contrast, saturation, sharpness |
| Video motion detection | 3 windows, adjustable sensitivity and threshold |
| Wireless connectivity | 802.11 b/g/n/ac, 2.4 & 5 GHz |
| Ethernet connection | 10/100Mbps RJ-45 |
| Simultaneous viewers | 10 |
| Operating temperature | 0°C – 40°C (32°F – 104°F) |
| Operating humidity | 20%-80% (non-condensing) RH |
| Max power consumption | 12 V DC, 5 W |
| Dimensions (WxH) | 2.75” x 2.06” x 3.67” |
| Two-Way Audio compatibility | Half-Duplex Requires Hardware Version 0101 and Firmware Version IP8168-ALAM-0100b9 + |
Note: For information about frame rate (FPS), see What is the frame rate for video?.
Network requirements
| Minimum bandwidth |
Without Two-Way Audio: 0.5 Mbps With Two-Way Audio: 1 Mbps For more information, see What are the internet service and bandwidth requirements for Alarm.com video devices?. |
|---|
LED Guide
| LED pattern | Status | Description |
|---|---|---|
|
Green Solid
|
Connected to the internet | Local network and internet connection with Alarm.com IP. |
|
Green Flashing
|
Local network connection |
Local network connection with local IP address, no internet. Note: If the LED does not go solid green after a few minutes, see Camera LED is blinking green. |
|
Red Solid
|
Power on, or no network connection |
Power on, system booting up typically 60-90 seconds. If solid red for longer than 60-90 seconds, then there is no local or Internet connection. |
|
Red Flashing
|
Camera powering on, or firmware update | Camera is powering on, or a firmware update is in progress. |
|
Blue Flashing
|
WPS mode |
WPS mode is active. To enter WPS mode, press and hold the WPS button for about 3 seconds. |
|
White Flashing
|
AP mode |
Wi-Fi access point (AP) mode is active. To enter AP mode, press and hold the WPS button for about 6 seconds. |
|
Red and Green Flashing
|
Factory reset |
The camera is restoring to factory default settings. Caution: If the camera is already installed, it may need to be removed from the Alarm.com account and re-added after a factory reset. To perform a factory reset, press and hold the reset button for about 10-15 seconds. |
Note: The WPS and reset options share the same button on the ADC-V522IR.